Tag: electrical tips

Burbank Electrician Explains Top Ways to Save on Your Electric Bill

Posted on | by K Hopkins | 1 Comment on Burbank Electrician Explains Top Ways to Save on Your Electric Bill

In today’s tough economic landscape, the idea of saving money on your electric bill is especially appealing. By following a few simple tips you will find that your monthly bill will shrink—giving you additional money to do the things you want to do. Here are a few tips to help you get started:

Use Fans – Fans use much less electricity than air conditioners. Installing an attic fan or even ceiling fans around your house can help you keep the AC use to a minimum. An electrician in Burbank from The Electric Connection can help with the installation project. (Click Here)

Use Energy Saving Bulbs – An energy saving bulb can produce as much light as a typical bulb but at a significant energy savings. These bulbs cost more up front but cut the electric bill by a significant sum.

Use Power Strips – Most electronic devices use power even when turned off because they remain in a standby mode. If you plug many of your products into power strips and flip the switch off at night you can reduce energy use.

Eliminate Appliances – Do you need all the electric appliances you use? Are there any you could replace with gas-powered appliances? Look over your appliance use and see where you can make changes.

Replace Old Electronics – Older electronics often use more electricity than newer ones. Newer products follow Energy Star standards so they are cheaper in terms of energy consumption. Replacing appliances often saves money in the long run.

Turn Down the Water Heater – If you use an electric water heater, you may not need it as high as it is. See if you can turn it down a few degrees and save money from heating costs.

Saving electricity isn’t just about reducing the impact on your wallet, it is good for the environment too. Contact The Electric Connection, the electrician Burbank residents trust, today and see what other changes may help your bottom line too.

Santa Monica Electrician – Considerations when You Lose Power

Posted on | by K Hopkins

Whether it is from storms or a fault in your home’s wiring, when the power goes out life gets difficult. Hopefully, you are able to talk to your Santa Monica electrical company and power is restored quickly. However, it is important to prepare yourself for the worst. Consider the following tips to make your next power outage more bearable. In the meantime, contact a Santa Monica electrician, such as The Electric Connection, to see if there are improvements you can make to your home’s wiring system to reduce the chances of a power outage.

Power Outage Tips

  • Avoid using candles during a power outage; a flashlight is much safer.
  • Keeping a battery-powered radio handy and listen to local programming. This can allow you to track the weather and prepare safety measures.
  • Turn off all electrical equipment that you were using when the power fails. This prevents a power surge when the power returns.
  • Try to avoid opening your freezer or refrigerator. This keeps the food within at a lower temperature.
  • Do leave one light turned on, so that you know when the power comes back.
  • Do not run a stand-alone generator in your home or garage—only use a properly installed outdoor generator.

Prepare Ahead by Keeping the Following Items on Hand

  • Flashlights
  • A portable radio
  • Batteries for flashlights and radio
  • A supply of fresh, bottled water
  • A small amount of food that does not require refrigeration or electricity to prepare—canned goods are an excellent choice.

If you are ready to make changes to your home’s electrical system, call the expert electrician in Santa Monica—The Electric Connection. You can also reach the company by searching for “electrician Santa Monica” and visit the website at ElectricConnection.com .  One of our experts will be happy to discuss your power options.

Glendale Electrician – Fun Facts About Electricity

Posted on | by K Hopkins | 2 Comments on Glendale Electrician – Fun Facts About Electricity

It seems like nearly everything operates on electricity today. All the modern conveniences and necessities that drive the world rely on electricity to keep them going. While we take for granted that when we plug in our television, for instance, it will power on and allow us to watch our favorite shows, there is actually a lot going on behind the scenes. While you will call a Glendale electrician, such as The Electric Connection, with any major problems, it is nice to understand the basic facts about the electricity you use on a daily basis— such as AC and DC current.

Facts about Electricity

  • Electricity travels at or near the speed of light. It would take less than two seconds for a light bulb to turn on if you had the switch on earth.
  • Nearly everyone knows that Thomas Edison invented the light bulb—he also opened the first electrical power plant just three years later.
  • Static electricity can create up to 3000 volts of power.
  • Nearly 70 people each year on average are killed by lightning strikes.
  • One lightning bolt creates enough electricity to service 200,000 homes.
  • The two types of electricity are static electricity and current electricity.
  • Electrical current is measured by an ampere , better known as an amp.
  • The earliest recorded notation of electricity occurred in the time of the ancient Egyptians—well before Benjamin Franklin’s experiments.
  • Speaking of Benjamin Franklin, he may not have discovered electricity, but he did prove the lightning is a form of electrical energy.

These fun facts barely scratch the surface of the information out there when it comes to electricity and other forms of power. If you have more in-depth questions, search for electrician Glendale by visiting The Electric Connection’s website at ElectricConnection.com or getting in touch with us today.

Los Angeles Electrician – Federal Pacific Panels

Posted on | by K Hopkins

Do you or does someone that you know have a Federal Pacific Electrical panel in their business or home? There are a number of reasons that these panels are unsafe, which means that they should be replaced as quickly as possible. One of the first reasons is simply because they are so old. Federal Pacific panels have not been installed in many years. The main reason that they should be replaced by your electrician in Los Angeles is because the circuit breakers in the panel may not always trip whenever they should. This can lead to some very serious issues with your home’s electrical system.

An Example

A couple years ago, one of our technicians were called out to inspect a circuit wire that appeared to have bubbled up. Whenever he arrived at the location, he discovered that this particular circuit had been overloaded so far that the sheath covering on the cable started to boil. Upon further inspection, he found out that the power for this particular cable came from a Federal Pacific electrical panel. What happened, was that the homeowner’s air conditioning unit was experiencing issues that caused it to seize up, continuously pulling more and more power from the panel. Rather than tripping like it should have, the circuit breaker remained on, leading to the boiling cable sheathe.

Although we were able to correct this problem relatively quickly, it could very easily have turned out much worse. This overloaded wire could have caught fire, or remained unnoticed and poorly insulated until it came into contact with a person or with another item that led to serious electrical shock or other injury.

The moral of the story is to have your home regularly inspected by a Los Angeles electrician for proper safety. For more safety tips or information about unsafe electrical panels, visit The Electric Connection at www.theelectricconnection.com.

Burbank Electrician – AC / DC What’s The Difference?

Posted on | by K Hopkins

Almost everything that we use on a daily basis operates on electricity. Every modern convenience that we have become used to relies on this fundamental utility. Without having a constant and reliable supply of this incredible technology, the world as we know it would grind to a screeching halt. In order to provide this powerful utility to our devices, two different forms of electricity have arisen: AC and DC.

AC means alternating current. This is the type of electricity that is used most frequently in devices that require a lot of power to operate. DC means Direct Current. It is most frequently found in devices that do not require a large amount of electricity to operate.

What’s The Difference?

DC was the original form of electricity that was generated by Thomas Edison. This form of electricity will send its current in a single direction only. This forms a direct loop. In most cases, DC current is only used in devices that use batteries. This means that any device that you have in your home that uses batteries operates on a DC system. When we charge these batteries, they transform the AC current from your wall into DC current.

AC power is the most common type of electricity, and is the form that your electrician in Burbank works with most frequently. The way that alternating current has been designed, it can move in both directions at the same time. This means that current will be present at every single point on the grid at any given time. If you use electricity from the power grid, then you plug into AC current every single day.

While you may not always think about it, having this reliable AC current is paramount to our everyday lives. For any further questions, or for help with any electrical issues that you have, don’t hesitate to get in touch with a technician at The Electric Connection. We also have a variety of additional resources available in our website at www.theelectricconnection.com.

Beverly Hills Electrician – The Importance of Surge Protection

Posted on | by K Hopkins

Were you aware of the fact that your home electrical equipment is frequently bombarded by very brief spikes in electrical power called power surges? These surges can slowly burn up the inside of your electronic devices, leading to a shorter lifespan than you should normally have. Although the most dangerous type of power surge comes from outside of your home and could destroy your devices in one fell swoop, this type of surge only accounts for about 30% of all power surges. The other 70% of power surges are generated from within your home. These surges are caused by some of your larger appliances like refrigerators and air conditioners.

A large power surge causes very fast, widespread damage. This can cause your wiring to burn up, devices to short circuit and motors to seize. Whenever you think of power surges, this is typically what comes to mind. The majority of power surges, however, remain unnoticed until your device meets an early end. This type of incremental power surge slowly eats away at the components of your electronics until they no longer function.

While it may seem like there is not much that you can do to prevent this, there is. One of the best ways to prevent against both large and incremental power surges is with surge suppression systems. This includes a combination of both local and whole house surge protection. For the largest level of protection, you should have your local electrician in Beverly Hills install a whole house surge protector. You can then protect especially sensitive devices with their own individual surge protectors.

By protecting your home from power surges, you help to ensure that your devices have a long lifespan. This not only keeps everything running as it should, but also saves you money in the long run. If you have any questions about whole house surge suppression, or would like to schedule an appointment for installation, get in touch with any of our technicians at The Electric Connection. You can also learn more from the resources at The Electric Connection website .

Electrician Los Angeles – A Few Practical Energy Conservation Tips

Posted on | by K Hopkins

Each and every household has at least one reason to conserve energy. This is a very basic idea, and should be important for everyone in all classes of society. By conserving energy you are being less wasteful, which can have a positive impact both on the environment and on your monthly energy bills. In most areas, electrical utility companies still use fossil fuels to provide our homes with the electricity that we use on a daily basis. This includes materials such as natural gas, coal and oil. The exhaust and other by-products of burning these fuels can be very harmful to the environment. Furthermore, they all have a limited supply that is rapidly declining due to the increased demand placed by humans.

What can you do to conserve energy at home?

One of the best places to start is to use your appliances mindfully. By this, we mean turning them off when they are not in use. For further power savings, you can even unplug them or turn an attached power strip off to avoid losing any “standby” power.

Your large home appliances, such as washing machines, dryers, refrigerators, air conditioners and heaters can account for up to two-thirds of the energy that you use at home. By unplugging them when not in use, or ensuring that they are only being used when necessary, you can make a significant dent in your electric bill. Take important steps such as turning your thermostat up when you leave the house, or improving your insulation. You can have your electrician in Los Angeles install time-saving devices such as programmable thermostats and dimmer switches to make this job even easier for you.

The bottom line is that everyone should be doing their best to conserve as much electricity as possible. While the effects may seem small, they truly add up and can benefit you both personally and everyone around you. For more ideas about energy conservation or help with an electrical installation or repair project, contact The Electric Connection. (Click Here).

Electrician in Los Angele Explains: Amps and Volts – What’s The Difference?

Posted on | by K Hopkins

Whenever looking at electrical devices or equipment, many people are confused by the difference between amps and volts, making it difficult for them to understand the purpose of each. By learning what each of these important electrical terms means, you can better use your electrical devices in a safe manner, which will help you avoid any electrical shocks, tripped breakers or other electrical mishaps.

Amps

One of the easiest ways to understand the difference between these electrical terms is to look at them from a more physical viewpoint. In order to do this, we will compare each with its plumbing equivalent. Imagine water running through a hose. Simply put, amps are just like the water that is flowing through the hose.

Volts

The amount of water running through a hose depends largely on the pressure that is forcing the water through the hose. In electrical terms, the amount of pressure forcing electricity through the wire is referred to as Volts. Whenever you combine the two, and multiply Amps x Volts, you get Watts. Watts would be the equivalent of the amount of electricity that is coming out of the wire at any given moment (Amps) and the amount of pressure pushing the electricity through the wire (Volts).

One of the most important reasons to understand these terms is to keep them in mind when using several different devices and appliances on a single circuit in your home. Each circuit in your home is protected by a circuit breaker that is designed to shut off the flow of power if the circuit becomes overloaded. By understanding how much electricity each appliance is designed to draw, you can more safely and effectively spread your appliances across your circuits.

If you notice that you have a circuit that is frequently tripping, or showing other signs of power drain, call an electrician right away. This could be a sign of deeper issues. If you are interested in more information about this or other electrical topics, our team at The Electric Connection has put together a solid list of related tips and articles in our website.

Electrician Pasadena – What Should You Do If There’s an Electrical Fire?

Posted on | by K Hopkins | 1 Comment on Electrician Pasadena – What Should You Do If There’s an Electrical Fire?

Although most electrical fires start very small, they can quickly spread into almost unmanageable proportions. This is especially true if the fire starts behind your walls. This can lead to a fire becoming very large before you even realize that it is there. Your best protection against an electrical fire is to prevent it from happening in the first place. If you must deal with one, however, you should always be prepared to take the proper course of action. Whenever faced with an electrical fire, your own personal safety is the number one priority. If the fire is too large for you to contain, or is growing too quickly, evacuate everyone out of the home immediately until a fire crew can make the area safe again.

If you are in a position to control the fire, start by shutting off all power to your building. Simply go to the electrical panel and shut off the main breaker until the fire is under control. If you do not already know where this is, find its location and make sure that it is never blocked or obstructed. Once the power has been shut off, you can attempt to smother the fire with a Class C fire extinguisher or baking soda. Do not ever throw water on an electrical fire. Water conducts electricity, which can result in you or someone else becoming electrocuted. Whenever the fire has been controlled, do not turn your electricity on until an electrician in Pasadena has inspected your wiring for safety. The last thing that you want is for a second fire to occur in the same place.

When it comes to using electricity in your home and businesses, your safety is more important than any other factor. Learn how to use your electrical system safely so that you can avoid any electrical fires, shocks or other mishaps. For more tips and information on fire safety and services, visit The Electric Connection website at www.theelectricconnection.com/.

Beverly Hills Electrician – The Importance of Home Electrical Safety

Posted on | by K Hopkins | 2 Comments on Beverly Hills Electrician – The Importance of Home Electrical Safety

Your electrical supply is one of the most important components of your home. Because it is used so frequently, we often take a properly functioning, safe and consistent electrical supply for granted. Because it has become such and integral and normal part of our everyday lives, it is easy to forget how powerful and potentially dangerous electricity can be. By knowing the basic rules of safe and effective use of electricity, you can greatly reduce that chance that you or a family member will be injured as a result of improper electrical usage.

When it comes to ensuring the electrical safety of your home, there are many things that you can do without the help of an electrician in Beverly Hills. Your number one goal is to reduce or eliminate any electrical safety hazards in your home. Be smart when using any electrical device. This includes extension cords, light bulbs, hair dryers and anything else. It only takes one mishap to cause some serious damage.

Here are a few tips:

  • Unplug It – Whenever you are not using a device or appliance, unplug it and safely stow the wire. This will remove it from your electrical system, while also eliminating any standby power draining that the device was guilty of.
  • Ventilate – Many of your devices generate a certain amount of heat, and require adequate ventilation space. This includes televisions, computers, ovens, microwaves and many others.
  • Follow Instructions – If your device has special instructions in regards to usage and placement, follow them!
  • No Extension Cords – Extension cords, when used as a permanent power solution, can become very dangerous hazards. Have your Beverly Hills electrician install a more convenient outlet instead.

Keeping your home and its electrical system safe is one of the most important things that you can do as a homeowner. To address any specific safety issues, feel free to call The Electric Connection at any time. Your safety is one of our top concerns.

Visit our company profile.